DAHON BB7 User Manual Page 7

  • Download
  • Add to my manuals
  • Print
  • Page
    / 14
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 6
BB7 and BB5 Installation & Set-Up Guide English
7SRAM Corporation July 2005
ALIGN THE CALIPER (BB7 ONLY)
A. Turn the inboard (closest to the wheel) knob clockwise until it
pushes the rotor into the position shown. Note that the rotor should
not be centered between the walls of the caliper body.
B. Turn the outboard pad adjustment knob in until it is firmly
squeezing the rotor against the inboard pad – thus immobilizing the
actuating arm. Your caliper is now in perfect position and ready to
be tightened. You’ll back the pads off again in a few moments.
C. Tighten the two CPS bolts that attach the caliper to the mounting bracket.
Tighten one and then the other, repeating until they are at the specified torque.
5
Rotor should be offset
to the outboard side of
the rotor slot. Ideal
ratio is 1/3 to 2/3.
TORQUE TO:
8-10 Nm
(70-90 in-lb)
Page view 6
1 2 3 4 5 6 7 8 9 10 11 12 13 14

Comments to this Manuals

No comments

Cisco Systems 5596t N5KC5596TFA manuály

Uživatelské manuály a uživatelské příručky pro Síťové přepínače Cisco Systems 5596t N5KC5596TFA.
Poskytujeme 1 manuály pdf Cisco Systems 5596t N5KC5596TFA ke stažení zdarma podle typů dokumentů: Uživatelský manuál


Tabulka s obsahem

Release 5.2(1)N1(1)

1

CONTENTS

3

Contents

4

78-26881-OL v

5

78-26881-OL vii

7

Audience

9

Document Conventions

9

Documentation Feedback

10

78-26881-OL xi

11

CHAPTER 1

13

2 78-26881-OL

14

About the Interface Command

15

Default UDLD Configuration

17

Interface Speed

18

Default CDP Configuration

19

About Port Profiles

20

About MTU Configuration

21

Configuring Unified Ports

22

Configuring the UDLD Mode

24

Configuring Interface Speed

25

Disabling Link Negotiation

26

Enabling or Disabling CDP

27

Port Profiles

31

Modifying a Port Profile

32

Inheriting a Port Profile

34

Example:

38

32 78-26881-OL

44

Routed Interfaces

45

Subinterfaces

46

VLAN Interfaces

47

Loopback Interfaces

47

Tunnel Interfaces

48

Configuring a Subinterface

49

Configuring a VLAN Interface

51

Monitoring Layer 3 Interfaces

54

MIBs for Layer 3 Interfaces

56

Configuring Port Channels

57

46 78-26881-OL

58

Compatibility Requirements

59

48 78-26881-OL

60

78-26881-OL 49

61

50 78-26881-OL

62

Understanding LACP

63

LACP ID Parameters

64

Channel Modes

64

LACP Marker Responders

65

Enabling LACP

69

Information About vPCs

77

Figure 5: vPC Architecture

78

Terminology

79

Supported vPC Topologies

80

78-26881-OL 69

81

70 78-26881-OL

82

78-26881-OL 71

83

72 78-26881-OL

84

Graceful Type-1 Check

85

Per-VLAN Consistency Check

86

78-26881-OL 75

87

78-26881-OL 79

91

Configuring vPCs

92

Creating a vPC Domain

93

Creating a vPC Peer Link

96

Enabling vPC Auto-Recovery

98

Before You Begin

100

Procedure

101

106 78-26881-OL

118

78-26881-OL IN-1

119

IN-2 78-26881-OL

120

78-26881-OL IN-3

121

IN-4 78-26881-OL

122





Další produkty a příručky pro Síťové přepínače Cisco Systems

Modely Typ Dokumentu
CISCO1805-E Uživatelský manuál   Cisco Systems CISCO1805-E User's Manual, 8 stránky